1000 kg Load Cell: Material Checks for LCX2003
Reference Standard: Relevant material and performance testing standards should be confirmed for the final application and procurement specification.
A 1000 kg load cell requirement can fit within the documented LCX2003 configuration, but capacity alone is not enough to finalize the sensor. The LCX2003 is listed as a two-axis load cell / multi-axis load cell with X-axis and Y-axis capacity ranges of 50 kg to 2 t, and its documented material entry is alloy / stainless steel. For a buyer, the practical task is therefore to confirm the required measuring range, material option, pivot-pin interface, operating environment, dimensions, and signal configuration as one coordinated specification.
Where a 1000 kg Load Cell Fits Within the LCX2003
The first purchasing decision is product identity. A search for a 1000 kg unit can describe only one part of the requirement: the desired capacity. The LCX2003 is not documented as a generic single-direction weighing element; it is described as a two-axis design intended to measure force in two directions simultaneously. That distinction affects the questions that should be resolved before material selection.
The catalog describes a pivot-pin design that can directly replace a shaft-pin installation. This matters in connecting mechanisms where adding force measurement through a conventional sensor arrangement could otherwise require mechanical changes. In this configuration, the sensor is not simply placed somewhere in a structure; it becomes part of the connection and force-transfer path.
For a 1000 kg requirement, the buyer should therefore confirm whether that target applies to the X axis, the Y axis, or the intended operating condition of both axes. The documented range provides the capacity envelope, but it does not define the buyer’s actual load case. The application team still needs to describe the direction of force, the connection geometry, and how the pin interface sits inside the mechanism.
A few verified LCX2003 data points help frame that discussion:
| Configuration item | Documented LCX2003 information |
|---|---|
| Measurement type | Two-axis load cell / multi-axis load cell |
| Capacity, X axis | 50 kg to 2 t |
| Capacity, Y axis | 50 kg to 2 t |
| 素材 | Alloy / stainless steel |
| Operating temperature | -20°C to +60°C |
| Installation concept | Pivot pin; direct replacement for shaft-pin installation |
Capacity and material should be discussed together because both belong to the same physical configuration. A buyer who specifies only “1000 kg” leaves unanswered questions about axis loading, interface geometry, environment, and the material variant to be supplied.
Material Options Documented for the LCX2003
The material entry for the LCX2003 lists alloy / stainless steel. Those are the documented options that can be used in a material-selection conversation. The available information does not identify a specific alloy grade or stainless-steel grade, so it would be unsafe to infer exact corrosion resistance, fatigue life, strength, hardness, weight, cost, surface treatment, or service life for either version.
That limitation is important because “alloy” and “stainless steel” are broad material families in engineering practice. Material behavior depends on details such as grade, heat treatment, processing route, geometry, surface condition, and the stresses generated by the real installation. None of those details should be assumed for this model unless they are confirmed in the final product documentation.
For procurement, this means the material field should be treated as a configuration item, not as a shortcut to a performance conclusion. If stainless steel is preferred because of a project requirement, the inquiry should state that preference and ask Ningbo SAINTBOND Intelligent Technology Co.,Ltd. to confirm the exact material supplied for the requested configuration. The same approach applies if the project calls for the documented alloy option.

The image above is useful as general load-cell context rather than as an identification image for the LCX2003. Different load-cell structures can use very different interfaces and force paths, which is exactly why material wording should never be separated from the specific model, drawing, and installation concept.
A material discussion also needs to remain connected to the sensor’s measured performance requirements. The LCX2003 catalog lists 1.0 to 1.5 mV/V sensitivity, a 5 to 12 VDC bridge supply with 10 VDC recommended, and an operating-temperature range of -20°C to +60°C. These are product specifications, but they do not prove that one documented material option performs better than the other. Instead, they help define the complete configuration that the buyer expects the delivered sensor to meet.
Signs the Material Specification Is Still Incomplete
- The request says only “stainless steel” or “alloy” without tying the choice to the LCX2003 configuration and drawing.
- The purchase description says “1000 kg” without defining the required X-axis and Y-axis loading conditions.
- The project assumes corrosion, fatigue, strength, or service-life differences between the two material options without documented model-specific evidence.
Match the Material Discussion to the Operating Environment
The LCX2003 is explicitly associated with aerospace, robot, lifting equipment, automobile, and mechanical automation applications. These application categories are useful for defining the environment a supplier needs to understand, but they do not establish that one material option is automatically correct for a particular industry.
A robot joint, lifting mechanism, vehicle-related assembly, aerospace mechanism, or automated machine can expose a sensor to very different mechanical interfaces and operating conditions. Even within the same application category, the installation may differ in force direction, available space, shaft-pin geometry, temperature, surrounding materials, cable routing, and access for installation or maintenance. The right procurement approach is to describe those conditions rather than substitute the application label for an engineering specification.
The verified -20°C to +60°C operating-temperature range is one concrete boundary that should be checked against the intended installation. If the expected environment falls within that range, the buyer can continue the configuration discussion; if the project expects conditions outside it, the catalog information alone does not establish suitability. That point should be resolved directly before ordering.
The direct-replacement pivot-pin concept also deserves attention in the material discussion. A shaft pin is part of the mechanical connection, so interface dimensions and how force enters the pin are fundamental to the measurement setup. The catalog states that overall dimensions can be customized according to customer requirements, which creates a practical path for matching the sensor to the mechanism. Customization, however, should be based on an agreed drawing or dimensional requirement rather than an assumption that a nominal 1000 kg capacity guarantees fit.
Buyers can also use the company’s load cell and force sensor overview as a general starting point when preparing a technical inquiry, while keeping the requested LCX2003 configuration tied to the model-specific information.
Material selection should therefore be discussed through questions such as: What is the real installation environment? Which material option is required by the project? What shaft-pin dimensions and mating interfaces must be matched? What are the actual X/Y force requirements? Does the expected temperature remain inside the documented operating range? These questions move the conversation from a broad material preference to an orderable engineering configuration without inventing performance differences that have not been documented.
Confirm Material, Dimensions, and Interfaces Before Ordering
The final step is to convert the material discussion into a controlled specification. For the LCX2003, several confirmed configuration variables can be reviewed together: 50 kg to 2 t capacity on both X and Y axes, alloy / stainless steel material options, customizable overall dimensions, the pivot-pin installation concept, and selectable standard signal outputs of 0-5 V, 0-10 V, or 4-20 mA.
The signal-output options are especially useful when mechanical and electrical teams are preparing the same purchase specification. They do not change the material decision, but they show why a load cell should be ordered as a complete sensing configuration rather than as a capacity number alone. A mechanically correct pin that cannot be integrated into the intended signal chain would still leave the project incomplete.
Dimensional customization should be handled with the same discipline. Because the catalog states that dimensions can be customized to customer requirements, the inquiry should provide the interface information needed to evaluate that customization. That may include the installation drawing, shaft-pin location, mating geometry, available envelope, and the intended force directions. The buyer should ask for the final drawing or agreed dimensional definition to be associated with the ordered configuration.
Material confirmation should also be explicit. If the purchase requires the documented alloy option, say so. If it requires the documented stainless-steel option, say so. If the exact material grade matters to the application, request that information rather than assuming it from the generic material label. The same principle applies to any desired surface treatment, environmental qualification, certification, inspection, or other requirement that is not stated in the available LCX2003 data: it must be separately confirmed instead of inferred.
Items to Confirm on the LCX2003 Purchase Specification
- Confirm that the required 1000 kg measurement sits within the intended X-axis and Y-axis configuration.
- State whether the requested documented material option is alloy or stainless steel.
- Describe the real application environment, including whether the sensor will be used in aerospace, robotics, lifting equipment, automotive equipment, or mechanical automation.
- Check that the expected operating temperature is compatible with the documented -20°C to +60°C range.
- Provide the pivot-pin interface and dimensional requirements needed for direct shaft-pin replacement or customization.
- Confirm whether customized overall dimensions are required and attach an installation drawing where practical.
- Select the required standard signal output when applicable: 0-5 V, 0-10 V, or 4-20 mA.
- Request written confirmation for any material grade, surface treatment, environmental resistance, certification, inspection, or other requirement not explicitly stated in the available LCX2003 specifications.
For buyers evaluating a 1000 kg load cell, the central material lesson is simple: alloy and stainless steel are documented LCX2003 options, but the available data does not justify assigning unverified performance advantages to either one. The reliable path is to connect the material choice with the two-axis capacity requirement, pivot-pin interface, operating environment, dimensional needs, and output configuration, then confirm the final supplied specification before release to production.
ポータブル軸重計、産業用ロードセル、力センサー、計量表示器、動的測定システムをお探しですか?お客様のプロジェクトに最適なソリューションをご提案いたします。
メーカー直販価格をご利用いただけるとともに、当社の専門家による技術サポートを24時間以内にご提供いたします。.
お見積もりのご依頼