1000 kg Load Cell Price in India: Signal Selection
A search for 1000 kg load cell price in India should not begin with a number alone. For the catalog-listed LCX2003, 1000 kg is within the documented 50 kg to 2 t capacity range on both X and Y axes, but the electrical configuration still needs to be defined before a meaningful quotation can be requested.
The LCX2003 is a pivot-pin, two-axis load cell with selectable integrated outputs of 0–5V, 0–10V, or 4–20mA. It also has documented 12V or 24V power-supply options for integrated-output configurations. These choices mean that two quotations for a nominally 1000 kg-capable LCX2003 may describe electrically different configurations even when the mechanical capacity requirement is the same.
Reference standard context: Confirm the calibration, electrical-integration, and performance standards required by the intended machine or control system. No specific model-level industry standard is stated for the LCX2003 in the available product information.
Electrical Configuration Behind a 1000 kg Load Cell Price in India Inquiry
The available information does not state an India-specific LCX2003 price. A buyer should therefore define the required capacity, two-axis measurement need, integrated output, power arrangement, and controller interface before requesting a configuration-specific quotation.
The first useful distinction is between mechanical capacity and electrical configuration. The LCX2003 is documented with X-axis and Y-axis capacity options from 50 kg to 2 t, so a 1000 kg requirement fits within that specified range. However, capacity alone does not determine what signal will arrive at the control cabinet.
The catalog lists three selectable integrated standard-signal outputs: 0–5V, 0–10V, and 4–20mA. A purchasing specification that says only “1000 kg load cell” leaves this interface choice unresolved. The receiving PLC, indicator, acquisition module, or control system must be considered before the output version is selected.
That matters because a controller expecting a voltage input cannot simply be assumed to accept a current-loop signal, and a device designed around a particular analog input range should not be paired with a different signal type without checking its input specification. The LCX2003 documentation confirms the available output choices, but it does not establish that one of them is universally more accurate, less expensive, or superior for every installation.
This is why price comparison should come after interface definition, not before it.

Select the LCX2003 Signal That the Controller Can Accept
The three documented integrated outputs should be treated as configuration choices, not interchangeable labels.
| LCX2003 integrated output | Buyer-side item to confirm |
|---|---|
| 0–5V | Verify that the receiving equipment accepts the required voltage-input format |
| 0–10V | Confirm that the controller or acquisition device is configured for this voltage range |
| 4–20mA | Confirm that the intended input channel is designed for the specified current signal |
This table does not imply a performance ranking. The product information does not state that one output has better accuracy, longer transmission capability, lower cost, or greater durability than another. Those claims should not be assumed from the signal format alone.
Instead, work backward from the receiving equipment. Identify the actual input module or controller that will process the load-cell signal and record its required signal format in the inquiry.
This becomes particularly important in automation projects where multiple devices share a control architecture. The LCX2003 is documented for force detection in connecting mechanisms used in areas such as robots, lifting equipment, automobiles, mechanical automation, and aerospace applications. In these systems, the sensor is only one component in a larger measurement chain.
The load cell may be mechanically suitable while still being electrically mismatched to the intended controller. Resolving that mismatch after purchasing can require changes elsewhere in the system. Defining the interface first reduces that risk.
The model also measures forces in two directions simultaneously. For an application where both X and Y forces matter, the project definition should preserve that two-axis requirement through the electrical and controller planning process. Treating the installation as a generic single-channel weighing task could overlook the reason this two-axis pivot-pin sensor was considered in the first place.
Keep Integrated-Output Power and Bridge Excitation Separate
One of the easiest specification mistakes is to combine different voltage figures from a datasheet as though they describe the same electrical function.
The LCX2003 documentation lists a 5–12VDC bridge supply range, with 10VDC recommended, alongside selectable integrated standard-signal outputs and 12V or 24V power-supply options. These are distinct documented electrical details and should not be casually substituted for one another.
The bridge-related specification belongs to the underlying sensing configuration. The 12V or 24V figures are associated with the documented integrated-output arrangements. A buyer preparing a price request should therefore state which configuration is being requested rather than writing a single voltage number without explaining what it refers to.
The catalog also lists 1.0–1.5mV/V sensitivity for the LCX2003. This is another reason to keep the underlying sensor characteristics separate from the selectable integrated outputs. A millivolt-per-volt sensitivity specification describes the sensing element differently from an integrated 0–5V, 0–10V, or 4–20mA output delivered for connection to downstream equipment.
For the purchasing team, the practical workflow is straightforward: document the receiving controller, identify the desired input format, confirm the available system power, and then state the corresponding LCX2003 electrical configuration in the quotation request.

Signs the Electrical Requirement Is Still Incomplete
- The inquiry specifies 1000 kg capacity but does not identify 0–5V, 0–10V, or 4–20mA output.
- The controller model is known, but its required analog input format has not been confirmed.
- A voltage such as 10V, 12V, or 24V appears in the requirement without stating whether it refers to bridge excitation or the integrated-output power arrangement.
Coordinate Signal Choice With the Two-Axis Measurement Task
The LCX2003 is not defined only by its capacity. Its pivot-pin structure is intended to measure force values in two directions simultaneously, and the catalog states that it can directly replace a shaft-pin installation. It also supports customizable overall dimensions.
Those characteristics affect how an electrical inquiry should be written.
If the application genuinely needs force information from two directions, the receiving system must be planned around the intended measurement architecture. Before procurement, identify how the machine controller or data-acquisition equipment will receive, identify, and use the required measurements. The available product information establishes the sensor’s two-axis measurement role but does not define a particular PLC program, channel map, terminal arrangement, or software implementation.
The documented performance values also belong to the LCX2003 as a specific model. They include nonlinearity of no more than ±0.3% F.S., lagging of no more than ±0.2% F.S., repeatability of no more than ±0.3% F.S., creep of no more than ±0.3% F.S. over 30 minutes, and mutual interference of no more than ±2.5% F.S.
These specifications should not be converted into claims about the relative performance of the three integrated output formats. The catalog confirms both the performance specifications and the available output selections, but it does not state that changing from 0–5V to 4–20mA, for example, improves those values.
The same evidence boundary applies to operating conditions. The LCX2003 has a documented operating-temperature range of -20°C to +60°C and a 120% F.S. safety overload specification. These are useful model-level characteristics, but they do not provide an India-specific price or establish a price premium for any particular electrical option.
The practical conclusion is that the electrical interface should be selected for system compatibility, while performance, mechanical installation, environment, and capacity remain separate parts of the technical review.
Define the Configuration Before Requesting a Price
A useful quotation request should make the requested LCX2003 configuration identifiable without forcing the supplier to guess what the control system needs.
Start with the mechanical requirement: state that the project requires a 1000 kg-capable configuration within the model’s documented 50 kg to 2 t X/Y range. Where the application requires simultaneous force measurement in two directions, say so explicitly.
Next, identify the electrical interface. Choose the required documented integrated signal format—0–5V, 0–10V, or 4–20mA—based on the input capability of the intended controller or acquisition hardware.
Then distinguish the power arrangement from bridge excitation. If an integrated-output version is required, identify the applicable 12V or 24V power option. If the inquiry concerns the underlying bridge specification, document that separately rather than combining it with the integrated-output supply requirement.
Mechanical customization should also remain visible in the request. The LCX2003 uses a pivot-pin structure, can directly replace shaft-pin installation, and supports customizable overall dimensions. Any dimensional requirement that affects the intended mechanism should therefore be defined before the final quotation rather than assumed to be identical across installations.
Details to Put in the RFQ Before Comparing Offers
- Confirm that the required load is 1000 kg within the LCX2003’s documented X/Y capacity range.
- State whether two-direction force measurement is required for the application.
- Specify 0–5V, 0–10V, or 4–20mA as the requested integrated output.
- Identify whether the relevant integrated-output power arrangement is 12V or 24V.
- Keep the 5–12VDC bridge specification, with 10VDC recommended, separate from integrated-output power requirements.
- Name the intended PLC, controller, indicator, or acquisition equipment and verify its accepted input type.
- Provide the mechanical installation requirements for the pivot-pin configuration.
- State any required dimensional customization before the quotation is finalized.
- Confirm environmental requirements against the model’s documented -20°C to +60°C operating range.
- Ask for the quotation to identify the exact electrical and mechanical configuration being priced.
Ningbo SAINTBOND Intelligent Technology Co.,Ltd. is identified as a China load cell and force sensor manufacturer, and the LCX2003 is documented within its product information. Buyers can review the company’s broader load cell and force sensor information when preparing a technical inquiry.
For an India-focused purchasing request, the important limitation is clear: no India-specific LCX2003 price is stated in the available product information. The useful next step is therefore not to infer a market price from the 1000 kg capacity label, but to request a quotation tied to the exact capacity, output, power, two-axis measurement, and dimensional configuration required by the system.
Вам нужны переносные весы для осей, промышленные тензодатчики, датчики силы, весовые индикаторы и системы динамических измерений? Ищете решения для своего проекта?
Получите цены напрямую от производителя и техническую поддержку от наших экспертов в течение 24 часов.
Запросить быстрое ценовое предложение